Recent content by SirHansen

Hi Anybody knows how to make this tread/diy "great again"? I want to update this diu so the pictures arw showing again. Anybody that have a good tips since the photobucket site are oreventing to post on 3rd party pages if you dont pay? Thanks! -Marius

Pm sent!

Hi All, Thank for all help. I did find the error, I am embarred to say that I actual had forgotten to plug in the fuel temp sensor when I reasemblied the fuelfilter cartrige. It was dark outside when i did the work,but today I did clearly se the mistake I had done.. I was not abke to delete the...

Hi Thank you for your reply! I purcased a Bosh filter,I will se if I can find the name/nr. It was also written Honda on the filter itself. It was a bit smaller than the original one. I borrowed a ODB reader and the failure codes I get now is PO 183. This is the same code IDid get by counting...

Hi I did change my diesel filter the other day, after I changed this I got the following fault codes. I have read out the codes by shorting the pin 4 and 9 at the odb connector under the dash. ABS lamp codes: 6-1 6 2 6 6 Engine lamp codes 12-5 18-3 18-4 18-5 When the car is idling the...

Hi, I believe that my problem was combined between the alternator clutch bearing, and auto tensior bearing. I enden up replacing both, no noice since.

Hi I dont know what has happend with all of the photolinks inside all of my DIY, it seems like they are gone. Anybody know how yo edit/restore them? If you want pictures I still have them.

Hi I noticed a that I had a rattling noice every time the air con clutch got engaged. I could not find just the bearing at my local Honda dealer, they only sold the complete clutch set, 5000 NOK (500GBP) So I decided to investigate this clutch set on my car to see if I could only replace the...

The crack in the manifold is not visible, the crack is so small that the smoke are just coming out when the manifold is cold. When the engine and manifold heats up, the leakage gets smaller or completely gone. It could also be the gasket that are gone, but either way you need to take the...

I had to send my unit in also, I treied to find any information about the sensor, but could not find anything on the net regarding the spec of the sensor that had failed. Here in Norway it cost around 5000 Nok (500GBP) to get the module repaired, and around 13 000 NOK (1300GBP) for as brand new...

I have the same issue on my Honda accord 2.2 ctdi. I believe the ***y is a ATE Teves MK60, but I have not verified this since my is still in the car. I realy do think this issue can be a soldering gone bad/cracked. This has been the issue on wv that the soldering has "cracked" I will get my...

So, today I remobed the pulley from the ac compressor, I was actally supriced on how easy it really was. I went to my lokal store to see if they did have this kind of bearing, but since this is a dual high presission bearing they did not have iy in the store. The marking on the bearing is dac...

I belive the bearing size is 30x52x22. I am going to see if I can start the work today on the car, just to verifty the size of the bearing. If I can only change the bearing inside the ac clutch pully I will save a lot of money ;)

Realy late reply here.. The tool grips on the edge of the tie rod, were the 2 flat spots are. Rgarding the allen key, I have a angeled allen key that I have used before. I am not sure what the correct name for that tool is in english...

Hi Today I found out that my bearing on the pulley for the aircon is faulty. Everythime the aircon clutch get engaged I hear a scweaky noice commong from the pulley. I did remove my belt to se if there was any slack on the pulley, and as I expected it was. My local dealer say I need to buy the...