Search results

yep that's correct it should but the shielding for the honda camera will strictly be tied to ground also that's why i used it and also saves having a long loop of wire....but cheers for pointing it out B) video pin 4 and 5 is what i used in the modified design....oh i don;t make it...

Just some hints on how to remove the navi for fitting an aux input or xcarlink or similar follow the post here first half way down from then you need to remove the DVD player for the navigation 4 10mm nuts/bolts , then you can withdraw it out and remove the wires....be careful the brackets...

That's cool...if it wasn't for that i would have thought someone had hammered something on lol ...ncie DIY!

hey there..have a read of this thread as well. Honda dealers won't have the equipment needed to do this sort of alignment, as fahad says a hunter machine is your best bet your nearest station seems to be Huw Lewis MOT Centre Unit 501 Glan Yr Afon Industrial Estate Llanbadarn ABERYSTWYTH...

I'll be putting a DIY of how to remove the upper panel soon so will update later :lol:

best of luck tell us how it goes..oh and did you use a file on the caliper pad holding areas to make it smooth..also when you had the pads out did you look at the condition of the pads/discs to see how they have worn?

hey faz, there have been issues with people fitting the clips and getting problems later...maybe because no clips are fitted to the bottom? but anyway i was always sceptical as to how the clips would help. Also have you cleaned the engine bay with water? By design a headlamp isn't a fully...

you're going to get good and bad reports from companies...especially small specialist companies like these. i think most of the time it's a people to people interaction thing...some people get along some don't. No doubt sometimes things do go wrong and it's these occasions where the negative...

-note i have placed the LEDs next to the clips so allows me to easily locate where to drill holes! -connect up and test -Time to mod the cover plate. you have to be a bit careful here..don't go too large and try to drill straight down...too large and the light will just reflect at you in the...

Tools ------- -Bell wire or similar -2 leds - LED holders - 2xpaper clips -1 k variable resistor (or approx 500ohm resistor or whatever you calculate) -2 pin 01" pcb connector and socket (or whatever you want) -2 screws -insulation for wiring - I used loom tape and some acoustic carpet I had...

updated now

Gov..glad you got the car back....kinda good service hey :D ...and have you taken off that tsx manifold and throttle body yet ;)....think it's gonna cause trouble. on the rolling road settings....you shouldn't change the settings from how you set it when you did the original or it will skew...

hmm a switch...yep never heard of it also :) ...masks all the way :D

yes..it's in plug B. As for the connector erm if you get the item from maplins and match it to how I've laid it out you'll be fine. Pin 6 and 7 are connected together Pin 5 is the +ve video signal (the center of the phono) and pin 4 is the ground for the video I'll probably make a few of...

I've seen some rear view mirrors that actually have a screen built into them now..yep they're small though,.....i'm not sure they are available here yet but it would fit with what you're trying to achieve :D

if they are still clear they may have gone through the lacquer? you could try what Saj suggests...may cover it..but we can't see the extent etc....you'll also have to keep replying after a while also.

just a tip..when you take out the bulb don't throw it away...there is a cover on it that you need to take off to put on the new one...for the replacement bulb just get white and put the cover on it :D

glad you finally got on with no problems

There is no earth point you need to install it's just the connector going to the headunit. I do remember someone having interference issues and i think this was down to insulation problems with his unit. I've tried cutting into the wiring on the unit and connecting it up so that it could be...

yes it can but i need to dig around i have the info somewhere..